Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » voice » pbx » grandstream_pbx
Trace:
voice:pbx:grandstream_pbx

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
voice:pbx:grandstream_pbx [2022/02/11 09:27]
gcooper 		voice:pbx:grandstream_pbx [2022/10/26 15:01] (current)
gcooper
Line 93: Line 93:
 === VoIP Trunks === === VoIP Trunks ===
  
-== Vitelity - Single Trunk ==+== Vitelity - Single Registration Account ==
  
-== Vitelity - Inbound ==+^Type            |Register SIP Trunk (dynamic IP)       | 
 +^Provider Name   |Vitelity                              | 
 +^Host Name       |inbound23.vitelity.net                | 
 +^Username        |SIP account username                  | 
 +^Password        |SIP account password                  | 
 +^AuthID          |SIP account username                  |
  
-^Type            |Peer for IP routing (static IP)       | +**Save**, then edit **Advanced Settings**:
-^                |Registration (dynamic IP)             | +
-^Provider Name   |vitel_inbound                         | +
-^Host Name       |inbound23.vitelity.net (registration) | +
-^                |64.2.142.90 (IP routing)              | +
-^Username        |SIP account username (registration)   | +
-^Password        |SIP account password (registration)   | +
-^AuthID          |SIP account username (registration)   | +
- +
-After saving, edit Advanced Settings:+
  
 ^Enable Heartbeat Detection (Qualify) |To monitor registration status     | ^Enable Heartbeat Detection (Qualify) |To monitor registration status     |
 ^Maximum # of Calls                   |To limit exposure                  | ^Maximum # of Calls                   |To limit exposure                  |
  
-== Vitelity - Outbound ==+----
  
-^Type            |Peer for IP routing (static IP)       | +:!: This section shows two trunks...incoming and outgoing.
-^                |Registration (dynamic IP)             | +
-^Provider Name   |vitel_outbound                        | +
-^Host Name       |outbound.vitelity.net (registration)  | +
-^                |64.2.142.95 (IP routing) (was 64.2.142.93) | +
-^Username        |SIP account username (registration)   | +
-^Password        |SIP account password (registration)   | +
-^AuthID          |SIP account username (registration)   | +
- +
-After saving, edit Advanced Settings: +
- +
-^Enable Qualify  |To monitor registration status        | +
-^Maximum # of Calls |To limit exposure                  | +
- +
- +
-----+
  
 == Vitelity - Inbound == == Vitelity - Inbound ==
Line 152: Line 133:
 ^Provider Name   |vitel_outbound                        | ^Provider Name   |vitel_outbound                        |
 ^Host Name       |outbound.vitelity.net (registration)  | ^Host Name       |outbound.vitelity.net (registration)  |
-^                |64.2.142.95 (IP routing) (was 64.2.142.93) |+^                |64.2.142.93 (IP routing)              |
 ^Username        |SIP account username (registration)   | ^Username        |SIP account username (registration)   |
 ^Password        |SIP account password (registration)   | ^Password        |SIP account password (registration)   |
Line 308: Line 289:
  
 {{ :voice:gateway:grandstream_monitor_vm_2.png?direct&728 |Monitor Shared Mailbox}} {{ :voice:gateway:grandstream_monitor_vm_2.png?direct&728 |Monitor Shared Mailbox}}
 +
 +===== Night Mode =====
 +
 +FIXME Needs testing! Problems!
 +
 +https://forums.grandstream.com/t/night-mode-toggle-blf-on-ucm62xx-resolved/39206
 +
 +http://onthewire.us/2019/10/11/grandstream-ucm-day-night-mode-and-time-holiday-mode/
 +
 +  - Go to ''Inbound Routes''
 +  - Go to ''Set Global Inbound Mode'' at the top
 +  - Select ''Enable'' and leave everything else as-is
 +  - ''Save'' & ''Apply''
 +  - Go back to ''Inbound Routes'' and edit your desired/normal inbound route
 +  - Select ''Enable Route-Level Inbound Mode'' in the middle of the page
 +  - Enter Any code you like for ''Inbound Mode Suffix'', for example enter ''80''
 +  - Enable ''Inbound Multiple Mode''
 +  - Setup your ''Mode 1'' route for night mode IVR/destination
 +  - ''Save'' & ''Apply''
 +  - Go to your deskphone and configure a BLF button with same value as ''Inbound Mode Suffix'', for example ''80''
  
 ===== Troubleshooting ===== ===== Troubleshooting =====
Line 316: Line 317:
  
 If you enable CallerID, but the analog line doesn't have that service, you may not get incoming calls. If you enable CallerID, but the analog line doesn't have that service, you may not get incoming calls.
 +
 +==== Transferring Calls to External Numbers ====
 +
 +**PBX Settings -> SIP Settings -> ToS -> RTP Keepalive -> 5**
 +
 +{{ :voice:pbx:grandstream_ucm_forward_to_external.png?direct&600 |Transferring to External Numbers}}
voice/pbx/grandstream_pbx.1644596838.txt.gz · Last modified: 2022/02/11 09:27 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki