Differences

This shows you the differences between two versions of the page.

--- voice:pbx:grandstream_pbx [2021/12/13 12:47]
gcooper
+++ voice:pbx:grandstream_pbx [2022/10/26 15:01] (current)
gcooper
@@ Line 1: / Line 1: @@
-====== Grandstream UCM6100 Series IP-PBX ======
+====== Grandstream UCM Series IP-PBX ======
 FIXME Needs to be updated for latest firmware.
@@ Line 93: / Line 93: @@
 === VoIP Trunks ===
-FIXME Just one registered trunk, perhaps with Outbound Proxy?
+== Vitelity - Single Registration Account ==
+^Type            |Register SIP Trunk (dynamic IP)       |
+^Provider Name   |Vitelity                              |
+^Host Name       |inbound23.vitelity.net                |
+^Username        |SIP account username                  |
+^Password        |SIP account password                  |
+^AuthID          |SIP account username                  |
+**Save**, then edit **Advanced Settings**:
+^Enable Heartbeat Detection (Qualify) |To monitor registration status     |
+^Maximum # of Calls                   |To limit exposure                  |
+----
+:!: This section shows two trunks...incoming and outgoing.
 == Vitelity - Inbound ==
@@ Line 117: / Line 133: @@
 ^Provider Name   |vitel_outbound                        |
 ^Host Name       |outbound.vitelity.net (registration)  |
-^                |64.2.142.95 (IP routing) (was 64.2.142.93) |
+^                |64.2.142.93 (IP routing)              |
 ^Username        |SIP account username (registration)   |
 ^Password        |SIP account password (registration)   |
@@ Line 126: / Line 142: @@
 ^Enable Qualify  |To monitor registration status        |
 ^Maximum # of Calls |To limit exposure                  |
+----
 === Inbound Routes ===
@@ Line 271: / Line 289: @@
 {{ :voice:gateway:grandstream_monitor_vm_2.png?direct&728 |Monitor Shared Mailbox}}
+===== Night Mode =====
+FIXME Needs testing! Problems!
+https://forums.grandstream.com/t/night-mode-toggle-blf-on-ucm62xx-resolved/39206
+http://onthewire.us/2019/10/11/grandstream-ucm-day-night-mode-and-time-holiday-mode/
+  - Go to ''Inbound Routes''
+  - Go to ''Set Global Inbound Mode'' at the top
+  - Select ''Enable'' and leave everything else as-is
+  - ''Save'' & ''Apply''
+  - Go back to ''Inbound Routes'' and edit your desired/normal inbound route
+  - Select ''Enable Route-Level Inbound Mode'' in the middle of the page
+  - Enter Any code you like for ''Inbound Mode Suffix'', for example enter ''80''
+  - Enable ''Inbound Multiple Mode''
+  - Setup your ''Mode 1'' route for night mode IVR/destination
+  - ''Save'' & ''Apply''
+  - Go to your deskphone and configure a BLF button with same value as ''Inbound Mode Suffix'', for example ''80''
 ===== Troubleshooting =====
@@ Line 279: / Line 317: @@
 If you enable CallerID, but the analog line doesn't have that service, you may not get incoming calls.
+==== Transferring Calls to External Numbers ====
+**PBX Settings -> SIP Settings -> ToS -> RTP Keepalive -> 5**
+{{ :voice:pbx:grandstream_ucm_forward_to_external.png?direct&600 |Transferring to External Numbers}}

Virtual Architects Support Wiki

User Tools

Site Tools

Differences

Page Tools