Differences

This shows you the differences between two versions of the page.

--- voice:pbx:freepbx:freepbx_provisioning [2015/03/13 13:21]
gcooper
+++ voice:pbx:freepbx:freepbx_provisioning [2017/10/04 14:13] (current)
gcooper
@@ Line 9: / Line 9: @@
 http://www.3cx.com/sip-phones/dhcp-option-66/
-:!: You will need to enable ''option66'' on your dhcp server so phones get their configuration on boot.
+:!: You will need to enable ''option 66'' on your dhcp server so phones get their configuration on boot.
+:!: You will need to open the firewall for UDP ports 67-69 for DHCP, BOOTP and TFTP.
 ===== Commercial EndPoint Manager =====
-http://schmoozecom.com/endpoint-manager.php
+https://www.freepbx.org/endpoint-manager/
+**Admin Guide**: http://wiki.freepbx.org/display/FPG/EPM-Admin+User+Guide
-**Admin Guide**: http://wiki.freepbx.org/display/FCM/EndPoint+Manager+Admin+User+Guide
+**Port Management**: http://wiki.freepbx.org/display/FPG/System+Admin+-+Port+Management
 **Supported Devices**: http://wiki.freepbx.org/display/FCM/EPM-Supported+Devices
@@ Line 55: / Line 59: @@
     - Configure as needed
       * Lots of settings
+        * Time Server -> Router IP (gateway IP)
       * Per phone model
   - Go to **Settings -> Endpoint Manager -> Extension Mapping**
@@ Line 61: / Line 66: @@
   - Reset the phone to factory defaults
     - Reboot the phone
+==== Multiple Accounts ====
+To provision multiple accounts to a phone (shared phone) **in Endpoint Manager**:
+  - Configure the first extension normally
+  - Edit the first extension just created
+  - Select ''Account 2''
+  - Choose the second extension
+  - Use the same template, model and MAC address
+**Endpoint Manager -> Extension Mapping -> <extension> -> Edit**
+{{ :voice:pbx:freepbx:freepbx_prov_second_extension.png?750 |FreePBX Provision Second Extension}}
+==== HTTP ====
+<file>
+http://<pbx-ip>:84
+</file>
 ===== Free OSS EndPoint Manager =====
-FIXME Unfinished
+FIXME Unfinished because we usually purchase the commercial EPM to support FreePBX development.
-Just install the OSS End Point Manager FreePBX module.
+Just install the **OSS End Point Manager** FreePBX module.
 http://www.the159.com/endpointman/tut.html
@@ Line 81: / Line 106: @@
   - You will also need to enable option66 on your dhcp server so the phones get the config on boot
-==== HTTP ====
+==== TFTP ====
-http://www.freepbx.org/forum/general-help/help-provisioning-polycom-phones-with-endpoint-manager
+**Verbose Logging**: http://wiki.freepbx.org/display/L1/Enable+TFTP+verbose+logging
-==== TFTP ====
 See also **[[networking:linux:dnsmasq|dnsmasq]]**
@@ Line 106: / Line 129: @@
 service dnsmasq restart
 </file>
-{{ :voice:pbx:freepbx_epm_1.png?direct&450|FreePBX OSS End Point Manager TFTP Setup}}
 **Connectivity -> OSS End Point Manager Advanced Settings**
-===== Troubleshooting =====
+{{ :voice:pbx:freepbx_epm_1.png?direct&750 |FreePBX OSS End Point Manager TFTP Setup}}
-==== Legacy Polycom Time ====
+===== Basefile Edits =====
-For some reason, the old IP301 and IP501 phones don't respect the DST settings in the template.
 **EndPoint Manager -> Basefile Edit -> Your Polycom Template -> Legacy**
+:!: Once saved, the customized setting will now be **listed at the bottom** of the list.
+:!: **Regenerate** the template, **rebuild** all your configs and **reboot** your phones when done making changes.
+==== Legacy Polycom ====
+For some reason, the old IP301 and IP501 phones don't respect the DST settings in the template.
 Scroll down to the setting for ''sntp.daylightSavings.enable'' and set it to ''0'', then click ''Submit Query'' to save.
-:!: The cusomized setting will now be listed at the bottom of the list.
+=== legacy_sip.cfg ===
+<file>
+   <sntp tcpIpApp.sntp.daylightSavings.enable="0"/>
+   <user_preferences up.oneTouchVoiceMail="1"/>
+</file>
+==== Grandstream DST ====
+There is no place in the template to set the proper time zone for Arizona or to turn off the observation of Daylight Savings Time.
-:!: Rebuild all your configs and reboot your phones.
+Scroll down to the setting for ''P64'' and set it to ''MST'' (for Arizona with no DST), then click ''Submit Query'' to save.

Virtual Architects Support Wiki

User Tools

Site Tools

Differences

Page Tools