Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » voice » pbx » freepbx » freepbx_e911
Trace:
voice:pbx:freepbx:freepbx_e911

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
voice:pbx:freepbx:freepbx_e911 [2015/02/01 19:35]
gcooper 		voice:pbx:freepbx:freepbx_e911 [2020/02/25 11:14] (current)
gcooper
Line 1: Line 1:
 ====== FreePBX e911 Emergency Dialing ====== ====== FreePBX e911 Emergency Dialing ======
  
-===== Simple Situations =====+:!: **New Requirements**: https://community.freepbx.org/t/freepbx-new-e911-compliance-features/64569 
 + 
 +:!: **New Requirements**: https://wiki.freepbx.org/display/FOP/Set+up+Emergency+Service%28E911%29+calling+requirements 
 + 
 +http://wiki.freepbx.org/display/FPG/Outbound+Routes+Configuration+Examples 
 + 
 +https://www.voip-info.org/asterisk-dialplan-patterns/ 
 + 
 +===== Simple Situations with One Location =====
  
 In simple situations, you can just add ''911'' to the ''Dial Patterns that will use this Route'' on the default outbound route and specify the caller ID for the outbound trunk or route. In simple situations, you can just add ''911'' to the ''Dial Patterns that will use this Route'' on the default outbound route and specify the caller ID for the outbound trunk or route.
Line 23: Line 31:
     * e911 location #1 physical address configured for DID #1     * e911 location #1 physical address configured for DID #1
     * e911 location #2 physical address configured for DID #2     * e911 location #2 physical address configured for DID #2
-  * An separate outbound route just for emergency calls named ''Emergency''+  * An separate outbound route named ''Emergency'' just for emergency calls
     * ''911'' dial pattern added/permitted/matched on the ''Emergency'' outbound route     * ''911'' dial pattern added/permitted/matched on the ''Emergency'' outbound route
 +      * But not on the default outbound route
     * ''Emergency'' flag enabled on the ''Emergency'' outbound route     * ''Emergency'' flag enabled on the ''Emergency'' outbound route
 +      * But not on the default outbound route
   * Configure the ''Route CID'' on the ''Emergency'' outbound route   * Configure the ''Route CID'' on the ''Emergency'' outbound route
     * Use DID #1 assuming location #1 is the primary or has the most extensions     * Use DID #1 assuming location #1 is the primary or has the most extensions
     * Select to ''Override Extension'' CID     * Select to ''Override Extension'' CID
-  * Configure all extension definitions at location #2+      * In case any extensions have their own CID defined 
 +  * Modify all extension definitions for extensions at location #2
     * Specify the ''Emergency CID'' as the DID for location #2     * Specify the ''Emergency CID'' as the DID for location #2
     * This will override the outbound ''Route CID'' when dialing from extensions at location #2     * This will override the outbound ''Route CID'' when dialing from extensions at location #2
    
voice/pbx/freepbx/freepbx_e911.1422844525.txt.gz · Last modified: 2015/02/01 19:35 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki