Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » voice » ata » spa3102
Trace:
voice:ata:spa3102

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
voice:ata:spa3102 [2017/04/11 08:52]
gcooper 		voice:ata:spa3102 [2021/10/27 12:15] (current)
gcooper
Line 5: Line 5:
 See also: **[[voice:ata:spa2100|Linksys/Sipura SPA-2100 ATA Connection Notes]]** See also: **[[voice:ata:spa2100|Linksys/Sipura SPA-2100 ATA Connection Notes]]**
  
-See also: **[[voice:gateway:grandstream_ata|Grandstream Analog Gateways and ATAs]]**+See also: **[[voice:ata:grandstream_ata|Grandstream Analog Gateways and ATAs]]**
  
-See also: **[[quick_guide:freepbx_ata|FreePBX with Analog Telephony Adapters]]**+See also: **[[voice:pbx:freepbx:freepbx_ata|FreePBX with Analog Telephony Adapters]]**
  
 ===== Seven Digit Dialing ===== ===== Seven Digit Dialing =====
Line 29: Line 29:
 For maximum bandwidth savings, use ''g.729a''.  Otherwise, choose (the default) ''g.711u'' (uncompressed) for best audio quality.  It's roughly 24Kbps vs. 92Kbps. For maximum bandwidth savings, use ''g.729a''.  Otherwise, choose (the default) ''g.711u'' (uncompressed) for best audio quality.  It's roughly 24Kbps vs. 92Kbps.
  
-Also, be sure to set the ''RTP Packet Size'' to ''0.020'' on the SIP tab.+:!: Be sure to set the ''RTP Packet Size'' to ''0.020'' on the SIP tab.
  
 ===== Paging ===== ===== Paging =====
Line 36: Line 36:
  
 http://wiki.freepbx.org/display/FOP/Using+an+SPA3102+FXO+Port+to+connect+with+Valcom+Paging+units http://wiki.freepbx.org/display/FOP/Using+an+SPA3102+FXO+Port+to+connect+with+Valcom+Paging+units
 +
 +==== Overview ====
 +
 +  - Configure a SIP Trunk and Outbound Route in FreePBX
 +  - Configure the SPA3102
 +  - Determine "Line-In-Use Voltage" of the FXO port and adjust it to match
 +    - Otherwise inbound calls in will result in a busy signal (SIP response 503 "Service Unavailable")
 +
 +
  
 ===== Enable the Web Interface on WAN ===== ===== Enable the Web Interface on WAN =====
  
-Whereas the WAN interface is used to connect to the SIP trunk provider, the web management of the SPA3102 is only available on the LAN interface of the unit.  If your SPA3102 is completely behind another firewall, you will find it more convenient to enable the web management on the WAN interface.+{{ :voice:ata:spa3102_connections.jpg?300|SPA3102 Connections}} 
 + 
 +Whereas the **WAN interface is used to connect to the SIP trunk provider**, the **web management of the SPA3102 is only available on the LAN interface** of the unit.  If your SPA3102 is completely behind another firewall, you will find it more convenient to enable the web management on the WAN interface.
  
 :!: Do **not** make the web interface accessible if your WAN interface is internet-accessible. :!: Do **not** make the web interface accessible if your WAN interface is internet-accessible.
voice/ata/spa3102.1491922325.txt.gz · Last modified: 2017/04/11 08:52 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki