Differences

This shows you the differences between two versions of the page.

--- voice:ata:spa3102 [2017/04/11 08:11]
gcooper created
+++ voice:ata:spa3102 [2021/10/27 12:15] (current)
gcooper
@@ Line 1: / Line 1: @@
-====== Cisco/Linksys SPA-3102 ATA Connection Notes ======
+====== Cisco/Linksys SPA3102 ATA Connection Notes ======
 FIXME This page is copied from another and is incorrect and incomplete.
@@ Line 5: / Line 5: @@
 See also: **[[voice:ata:spa2100|Linksys/Sipura SPA-2100 ATA Connection Notes]]**
-See also: **[[voice:gateway:grandstream_ata|Grandstream Analog Gateways and ATAs]]**
+See also: **[[voice:ata:grandstream_ata|Grandstream Analog Gateways and ATAs]]**
-See also: **[[quick_guide:freepbx_ata|FreePBX with Analog Telephony Adapters]]**
+See also: **[[voice:pbx:freepbx:freepbx_ata|FreePBX with Analog Telephony Adapters]]**
 ===== Seven Digit Dialing =====
-If you use a SIP trunk provider that requires 10 digits, modify the Dialplan in the Line1 (or Line2) settings by adding ''<:520>'' to the 7-digit section:
+{{ :voice:ata:spa3102.jpg?300|SPA3102}}
+If you use a SIP trunk provider that requires 10 digits, modify the Dialplan in the Line1 (or Line2) settings by inserting ''<:520>'' to the 7-digit section:
 <file>
@@ Line 27: / Line 29: @@
 For maximum bandwidth savings, use ''g.729a''.  Otherwise, choose (the default) ''g.711u'' (uncompressed) for best audio quality.  It's roughly 24Kbps vs. 92Kbps.
-Also, be sure to set the ''RTP Packet Size'' to ''0.020'' on the SIP tab.
+:!: Be sure to set the ''RTP Packet Size'' to ''0.020'' on the SIP tab.
+===== Paging =====
+In our limited experience, paging amplifiers are usually connected to an FXO port of a PBX.  **The SPA3102 includes an FXO port**.
+http://wiki.freepbx.org/display/FOP/Using+an+SPA3102+FXO+Port+to+connect+with+Valcom+Paging+units
+==== Overview ====
+  - Configure a SIP Trunk and Outbound Route in FreePBX
+  - Configure the SPA3102
+  - Determine "Line-In-Use Voltage" of the FXO port and adjust it to match
+    - Otherwise inbound calls in will result in a busy signal (SIP response 503 "Service Unavailable")
+===== Enable the Web Interface on WAN =====
+{{ :voice:ata:spa3102_connections.jpg?300|SPA3102 Connections}}
+Whereas the **WAN interface is used to connect to the SIP trunk provider**, the **web management of the SPA3102 is only available on the LAN interface** of the unit.  If your SPA3102 is completely behind another firewall, you will find it more convenient to enable the web management on the WAN interface.
+:!: Do **not** make the web interface accessible if your WAN interface is internet-accessible.
+The default settings will leave the SPA3102 in an un-managable state if you only connect the WAN port to your internal network...a common configuration.  One would have to connect a portable PC to the LAN interface to administer the unit.
+These steps will enable the web interface on the WAN port:
+  - Plug in an analog phone or 'butt set' into the Phone port
+  - Dial ''****'' (four asterisks) for the (audible) main menu
+  - Dial ''110#'' for the IP submenu
+  - Dial ''7932#'' then
+  - Dial ''1#'' to confirm

Virtual Architects Support Wiki

User Tools

Site Tools

Differences

Page Tools