Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » voice » ata » spa2100
Trace:
voice:ata:spa2100

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
voice:ata:spa2100 [2012/04/23 22:17]
gcooper 		voice:ata:spa2100 [2017/03/15 14:40] (current)
gcooper
Line 8: Line 8:
  
 http://michigantelephone.wordpress.com/2007/11/16/linksys-and-sipura-adapter-users-check-your-rtp-packet-size-and-newtork-jitter-level/ http://michigantelephone.wordpress.com/2007/11/16/linksys-and-sipura-adapter-users-check-your-rtp-packet-size-and-newtork-jitter-level/
 +
 +https://portal.vitelity.net/support/pap2a.php
 +
 +https://portal.vitelity.net/support/pap2b.php
  
 ===== Where Did It Come From? ===== ===== Where Did It Come From? =====
  
-If your SPA2100 came pre-programmed from a VoIP provider, you may need to take extra care and may run into certain limitations.  We have even heard that sometimes line 1 is not usable...+:!: If your SPA2100 came pre-programmed from a VoIP provider, you may need to take extra care and may run into certain limitations.  We have even heard that sometimes line 1 is not usable...
  
 When trying to gain admin access to a SPA2100, connect your PC to the LAN interface and set it to DHCP mode.  Once you get assigned an IP address via DHCP, try accessing the unit with a web browser pointed to '.1' within the IP address range to which you were assigned.  This can save you a lot of troubleshooting. When trying to gain admin access to a SPA2100, connect your PC to the LAN interface and set it to DHCP mode.  Once you get assigned an IP address via DHCP, try accessing the unit with a web browser pointed to '.1' within the IP address range to which you were assigned.  This can save you a lot of troubleshooting.
Line 33: Line 37:
 Default the SPA-2100 to factory defaults using a standard telephone plugged into port 1.   Default the SPA-2100 to factory defaults using a standard telephone plugged into port 1.  
  
-Dial ****73738# then: 1#  to confirm+Dial 
 + 
 +<file> 
 +****73738# 
 +</file> 
 + 
 +then: 
 + 
 +<file> 
 +1# 
 +</file> 
 + 
 +to confirm.
  
   * The WAN interface defaults to DHCP, which is usually what you want.   * The WAN interface defaults to DHCP, which is usually what you want.
Line 78: Line 94:
         This dial plan allows 7 and 11 digit dialing only: (xxxxxxx|xxxxxxxxxxx)         This dial plan allows 7 and 11 digit dialing only: (xxxxxxx|xxxxxxxxxxx)
         This dial plan allows for faster dialing in most cases: ([2-9]xxxxxxS0|1xxxxxxxxxxS0|*xx*|x.)         This dial plan allows for faster dialing in most cases: ([2-9]xxxxxxS0|1xxxxxxxxxxS0|*xx*|x.)
 +        The default plan is: (*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.)
  
 ===== Line 2 ===== ===== Line 2 =====
voice/ata/spa2100.1335241056.txt.gz · Last modified: 2012/04/23 22:17 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki