Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » voice » ata » spa2100
Trace:
voice:ata:spa2100

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
voice:ata:spa2100 [2012/04/23 22:08]
gcooper 		voice:ata:spa2100 [2017/03/15 14:40] (current)
gcooper
Line 3: Line 3:
 ===== More Info ===== ===== More Info =====
    
-http://voxilla.com/voxilla-stories/voxilla-how-to-guides/using-the-spa2000-with-asterisk-417.html+http://voxilla.com/2003/12/24/using-a-linksyssipura-spa-with-asterisk/ 
 + 
 +http://voxilla.com/2003/12/06/using-a-linksyssipura-spa-with-voicepulse-connect/
  
 http://michigantelephone.wordpress.com/2007/11/16/linksys-and-sipura-adapter-users-check-your-rtp-packet-size-and-newtork-jitter-level/ http://michigantelephone.wordpress.com/2007/11/16/linksys-and-sipura-adapter-users-check-your-rtp-packet-size-and-newtork-jitter-level/
 +
 +https://portal.vitelity.net/support/pap2a.php
 +
 +https://portal.vitelity.net/support/pap2b.php
  
 ===== Where Did It Come From? ===== ===== Where Did It Come From? =====
  
-If your SPA2100 came pre-programmed from a VoIP provider, you may need to take extra care and may run into certain limitations.  We have even heard that sometimes line 1 is not usable...+:!: If your SPA2100 came pre-programmed from a VoIP provider, you may need to take extra care and may run into certain limitations.  We have even heard that sometimes line 1 is not usable...
  
 When trying to gain admin access to a SPA2100, connect your PC to the LAN interface and set it to DHCP mode.  Once you get assigned an IP address via DHCP, try accessing the unit with a web browser pointed to '.1' within the IP address range to which you were assigned.  This can save you a lot of troubleshooting. When trying to gain admin access to a SPA2100, connect your PC to the LAN interface and set it to DHCP mode.  Once you get assigned an IP address via DHCP, try accessing the unit with a web browser pointed to '.1' within the IP address range to which you were assigned.  This can save you a lot of troubleshooting.
Line 26: Line 32:
  
 ===== Factory Reset ===== ===== Factory Reset =====
 +
 +:!: Note that this will not necessarily reset certain settings programmed permanently into your unit by the original vendor.
  
 Default the SPA-2100 to factory defaults using a standard telephone plugged into port 1.   Default the SPA-2100 to factory defaults using a standard telephone plugged into port 1.  
  
-Dial ****73738# then: 1#  to confirm+Dial 
 + 
 +<file> 
 +****73738# 
 +</file> 
 + 
 +then: 
 + 
 +<file> 
 +1# 
 +</file> 
 + 
 +to confirm.
  
   * The WAN interface defaults to DHCP, which is usually what you want.   * The WAN interface defaults to DHCP, which is usually what you want.
Line 74: Line 94:
         This dial plan allows 7 and 11 digit dialing only: (xxxxxxx|xxxxxxxxxxx)         This dial plan allows 7 and 11 digit dialing only: (xxxxxxx|xxxxxxxxxxx)
         This dial plan allows for faster dialing in most cases: ([2-9]xxxxxxS0|1xxxxxxxxxxS0|*xx*|x.)         This dial plan allows for faster dialing in most cases: ([2-9]xxxxxxS0|1xxxxxxxxxxS0|*xx*|x.)
 +        The default plan is: (*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.)
  
 ===== Line 2 ===== ===== Line 2 =====
Line 84: Line 105:
     type=friend     type=friend
     username=your_user_name     username=your_user_name
-    secret=5000+    secret=your_password
     mailbox=5000     mailbox=5000
     host=dynamic     host=dynamic
     qualify=3000     qualify=3000
     context=internal     context=internal
-    callerid="your_ID" <5000>+    callerid="Your Name" <5000>
     canreinvite=no     canreinvite=no
     pickupgroup=1     pickupgroup=1
Line 99: Line 120:
 ===== Provisioning ===== ===== Provisioning =====
  
-First off, we don't have a stock SPA-2100 to test with, so these instructions are incomplete.  Our unit came from a VoIP provider that preconfigured certain things.  We had very limited (unpredictable) auto-provisioning results from our unit.  We'd love to 'unlock' it from the original VoIP provider's pre-provisioning, but haven't been able to so far.+:!: First off, we don't have a stock SPA-2100 to test with, so these provisioning instructions are incomplete.  Our unit came from a VoIP provider that preconfigured certain things.  We had very limited (unpredictable) auto-provisioning results from our unit.  We'd love to 'unlock' it from the original VoIP provider's pre-provisioning, but haven't been able to so far.
  
 These instructions assume you have a TFTP server and a DHCP server with option 66 support already installed on your LAN.  These instructions assume you have a TFTP server and a DHCP server with option 66 support already installed on your LAN. 
Line 143: Line 164:
     </Resync_Periodic>     </Resync_Periodic>
  
-==== Backup/Restore Tool ====+===== Backup/Restore Tool =====
  
 http://www.opensky.ca/~jdhildeb/software/spaconf/ http://www.opensky.ca/~jdhildeb/software/spaconf/
  
  
voice/ata/spa2100.1335240485.txt.gz · Last modified: 2012/04/23 22:08 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki