User Tools
virtualization:2x:2x_thin_client_server
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
virtualization:2x:2x_thin_client_server [2014/11/13 10:40] jcooper |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== 2X ThinClient Server ====== | ||
| - | ===== Enable PXE Boot Server ===== | ||
| - | |||
| - | It is necessary to enable the PXE Boot Server. | ||
| - | |||
| - | - In the 2X Remote Application Server Console Click on " | ||
| - | - Under Farm click on " | ||
| - | - Right click on the current Gateway, choose Properties. | ||
| - | - Click the " | ||
| - | - Under Thin Client network Boot Support tick box next to enable that option | ||
| - | - Enable DHCP proxy (Port 67) | ||
| - | - Click OK and then the Apply button | ||
| - | |||
| - | :!: Any time you make a change click the Apply button if it is lit up! You may NOT be prompted to do so when necessary! | ||
| - | |||
| - | ===== Add a Thin Client to PXE Boot ===== | ||
| - | |||
| - | This will boot a Thin Client/PC to the 2X OS | ||
| - | |||
| - | - Configure the PC/Thin Client to PXE boot (Boot to LAN) in BIOS | ||
| - | - Boot to PXE and note MAC Address displayed during boot IE 74-D4-35-E5-67-9A | ||
| - | - In the 2X Remote Application Server Console Click on " | ||
| - | - Click the + (add) button | ||
| - | - Enter the MAC Address, click Next | ||
| - | - Enter descriptive Hostname or leave at default TC-(MAC Address) | ||
| - | - If you have a group configured for this device select that group | ||
| - | - If Boot Method is other than " | ||
| - | - Use defaults on other screens if the group is configured or untick Use Group settings and configure | ||
| - | - Click Finish and then the Apply button | ||
| - | |||
| - | ==== Define Video for proper operation ==== | ||
| - | |||
| - | If the default auto detection does not work for video you can force drivers and settings. | ||
| - | |||
| - | - In the Client Manager section right click the device to be configure and select Properties | ||
| - | - Click the Hardware Tab, Untick Use Group Settings, Advanced Button, Force Display Settings Button | ||
| - | - Tick "Force Display Settings" | ||
| - | - Set the resolution to the native resolution of the monitor | ||
| - | - Click OK, OK, OK | ||
| - | - Click the Apply button | ||
| - | |||
| - | :!: If video is not acceptable try other possible options of manufacturer if available. | ||
| - | |||
| - | http:// | ||
| - | |||
| - | **32-Bit** | ||
| - | |||
| - | Works with AppArmor and [[selinux]] | ||
| - | |||
| - | yum install compat-libstdc++-33.i386 | ||
| - | |||
| - | rpm -Uvh 2XThinClientServer_i386.rpm | ||
| - | |||
| - | 2Xthinclientserver_conf.sh | ||
| - | |||
| - | Uses (installs) [[mysql]] (3306), apache (980, 943), dhcphelper (67, 4011) and tftp (69) | ||
| - | |||
| - | Beta version supposedly supports ' | ||
virtualization/2x/2x_thin_client_server.1415900413.txt.gz · Last modified: 2014/11/13 10:40 by jcooper
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
