Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » quick_guide » vpn_l2tp_windows
Trace:
quick_guide:vpn_l2tp_windows

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
quick_guide:vpn_l2tp_windows [2016/05/14 12:22]
jcooper 		quick_guide:vpn_l2tp_windows [2020/09/30 14:46] (current)
jcooper
Line 1: Line 1:
 ====== L2TP VPN Windows Client setup ====== ====== L2TP VPN Windows Client setup ======
  
-:!: VPN Connections can be quite useful for remote control or small file access.  Limited bandwidth makes it less effective for data transfer volumes commonly seen on a LAN.  +See also **[[networking:windows:windows_vpn|Windows VPN Notes]]** 
 + 
 +:!: VPN Connections can be quite useful for remote control or small file access.  However, limited bandwidth makes it less effective for data transfer volumes commonly seen on a LAN. 
 + 
 +:!: For IP routing to work the IP address of the network you are connecting from must be different than the network you are connecting to.  If they are the same the connection will complete but data will not transfer.  
  
 ====== Windows 7 ====== ====== Windows 7 ======
Line 7: Line 11:
 https://www.youtube.com/watch?v=tpgEqzwj_OQ Start at 1:50 for Windows 7 client setup https://www.youtube.com/watch?v=tpgEqzwj_OQ Start at 1:50 for Windows 7 client setup
  
-  * Control Panel -> Network and Sharing Center  +  * Control Panel -> ''Network and Sharing Center''  
-  * Setup a New Connection or Network +  * Click ''Setup a New Connection or Network'' 
-  * Connect to a Workplace -> Next+  * ''Connect to a Workplace'' -> Next
   * Leave at ''No create a new connection'' -> Next if asked   * Leave at ''No create a new connection'' -> Next if asked
   * Click ''Use my Internet connection''   * Click ''Use my Internet connection''
Line 18: Line 22:
   * Click ''Change Adapter Settings''   * Click ''Change Adapter Settings''
   * Right Click the adapter you just created -> Properties   * Right Click the adapter you just created -> Properties
-  * On Security tab Type of VPN select Layer 2...+  * On Security tab Type of VPN select ''Layer 2...''
   * Uncheck ''Challenge Handshake Authentication...'' -> Advanced   * Uncheck ''Challenge Handshake Authentication...'' -> Advanced
   * Check ''Use preshared key'' and enter the Secret given to you by your administrator -> OK   * Check ''Use preshared key'' and enter the Secret given to you by your administrator -> OK
Line 27: Line 31:
 ====== Windows 8.1 ====== ====== Windows 8.1 ======
  
-  * Control Panel -> Network and Sharing Center +  * Control Panel -> ''Network and Sharing Center'' 
   * Click ''Setup a New Connection or Network''   * Click ''Setup a New Connection or Network''
   * Connect to a Workplace -> Next   * Connect to a Workplace -> Next
Line 33: Line 37:
   * Click ''Use my Internet connection''   * Click ''Use my Internet connection''
   * ''Internet Address'' is hostname or IP address of L2TP server given to you by your administrator   * ''Internet Address'' is hostname or IP address of L2TP server given to you by your administrator
-  * ''Destination Name'' is your label for the connection -> Create+  * ''Destination Name'' is your label for the connection -> ''Create''
   * Click ''Change Adapter Settings''   * Click ''Change Adapter Settings''
   * Right Click the adapter you just created -> Properties   * Right Click the adapter you just created -> Properties
-  * On Security tab Type of VPN select Layer 2... +  * On Security tab Type of VPN select ''Layer 2...'' 
-  * For Data encryption select ''Require encryption (disconnect...''+  * For Data encryption select ''Require encryption...''
   * Check ''Allow these protocols''   * Check ''Allow these protocols''
   * Check ''Microsoft CHAP Version 2 (MS-CHAP v2)''   * Check ''Microsoft CHAP Version 2 (MS-CHAP v2)''
-  * Click ''Advanced'' enter the Secret given to you by your administrator -> OK -> OK+  * Click ''Advanced settings'' and tick ''Use preshared ...'' enter the Secret given to you by your administrator -> OK -> OK
  
 :!: It is important that you disconnect as soon as you are done using the VPN.  All Internet traffic will go through the VPN until you disconnect. :!: It is important that you disconnect as soon as you are done using the VPN.  All Internet traffic will go through the VPN until you disconnect.
Line 56: Line 60:
   * Right Click the adapter you just created -> Properties   * Right Click the adapter you just created -> Properties
   * On Security tab Type of VPN select ''Layer 2...''   * On Security tab Type of VPN select ''Layer 2...''
-  * For Data encryption select ''Require encryption (disconnect...''+  * For Data encryption select ''Require encryption...''
   * Check ''Allow these protocols''   * Check ''Allow these protocols''
   * Check ''Microsoft CHAP Version 2 (MS-CHAP v2)''   * Check ''Microsoft CHAP Version 2 (MS-CHAP v2)''
-  * Click Advanced enter the Secret given to you by your administrator -> OK -> OK+  * Click ''Advanced Settings'' button, tick ''Use preshared key...'' and enter the Secret given to you by your administrator -> OK -> OK
  
 :!: It is important that you disconnect as soon as you are done using the VPN.  All Internet traffic will go through the VPN until you disconnect. :!: It is important that you disconnect as soon as you are done using the VPN.  All Internet traffic will go through the VPN until you disconnect.
Line 76: Line 80:
   * Click the L2TP connection you created   * Click the L2TP connection you created
   * Click ''Disconnect''   * Click ''Disconnect''
 +
 +====== Browse a network share ======
 +
 +:!: Typically NetBIOS (name resolution) does not work over a VPN.  You must know the IP address of the machine you are trying to access.
 +
 +  * In the ''Run'' field type \\(ip address of machine) e.g. \\192.168.1.2
 +  * Enter credentials when prompted save if desired
 +  * The resulting window will show shared resources
 +  * Double click to open shares
 +  * You can right click a share and select ''Map network drive...'' to assign a drive letter
 +
 + 
 +
  
quick_guide/vpn_l2tp_windows.1463250152.txt.gz · Last modified: 2016/05/14 12:22 by jcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki