Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » networking » wireless » unifi
Trace:
networking:wireless:unifi

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
networking:wireless:unifi [2023/05/12 08:26]
gcooper 		networking:wireless:unifi [2024/08/19 11:17] (current)
gcooper
Line 1: Line 1:
 ====== Ubiquiti Unifi ====== ====== Ubiquiti Unifi ======
 +
 +**Optimize Your Network**: https://help.ui.com/hc/en-us/articles/360012947634-UniFi-Network-Optimizing-Wireless-Speeds
  
 **User Guide**: http://dl.ubnt.com/guides/UniFi/UniFi_Controller_V4_UG.pdf **User Guide**: http://dl.ubnt.com/guides/UniFi/UniFi_Controller_V4_UG.pdf
Line 27: Line 29:
   * Integrated billing system available   * Integrated billing system available
  
-===== Controller Installation =====+<note tip>Consider using a Docker-based configuration.</note> 
 + 
 +===== Server ===== 
 + 
 +[[internet:mail:zimbra:zimbra_ose#server_preparation|Server Prep]]   
 + 
 +==== Unifi Installation ==== 
 + 
 +:!: Unifi Controller seems to be easy to install, run and update under **Docker**.  See below.
  
 https://pimylifeup.com/ubuntu-unifi-controller/ https://pimylifeup.com/ubuntu-unifi-controller/
  
-:!: This is for a minimal Ubuntu 22.04 LTS Server with 2 vCPU, 2GB RAM and a 20GGB vHD.+:!: This is for a minimal **Ubuntu 22.04** LTS Server with **2 vCPU**, **2GB RAM** and a **20GB vHD**.
  
 <file> <file>
Line 72: Line 82:
 </file> </file>
  
-==== Management ====+===== Management =====
  
-=== Browser ===+==== Browser ====
  
 https://ip.of.controller:8443 https://ip.of.controller:8443
Line 81: Line 91:
 ^Default Password |''123456''   | ^Default Password |''123456''   |
  
-=== SSH ===+==== SSH ====
  
 ^Default Username |''ubnt''     | ^Default Username |''ubnt''     |
Line 92: Line 102:
 :!: Be aware that under **Settings -> Networks -> Edit** you will find a **DHCP Server enabled**. :!: Be aware that under **Settings -> Networks -> Edit** you will find a **DHCP Server enabled**.
  
-**Select the site -> Settings -> Site**+**Select the site -> Settings -> System**
  
   * ''Site Name''   * ''Site Name''
   * ''Country''   * ''Country''
   * ''Time Zone''   * ''Time Zone''
-  * ''Device Authentication'' 
  
 **Select the site -> Settings -> Wireless Networks** **Select the site -> Settings -> Wireless Networks**
Line 130: Line 139:
 ===== Guest Networks ===== ===== Guest Networks =====
  
-**Guest FAQ**: http://wiki.ubnt.com/UniFi_FAQ#Guest_Access+Simple guest access uses single DHCP server and restricts access to Internet only.
  
-**Guest Doc**: https://help.ubnt.com/hc/en-us/articles/115000166827-UniFi-Wireless-Guest-Network-Setup +<note tip>These steps are no longer correct for Controller V8. Guest networks are now created by selecting ''Manual'' configuration and enabling ''Hotspot Portal''.  You configure the user experience by managing the Hotspot Portal.</note>
- +
-**If Using VLANs**: https://help.ubnt.com/hc/en-us/articles/219654087-UniFi-Using-VLANs-with-UniFi-Wireless-Routing-Switching-Hardware +
- +
-Simple guest access uses single DHCP server and restricts access to Internet only.+
  
   * To **restrict bandwidth of guests**, create a "Guests" User Group   * To **restrict bandwidth of guests**, create a "Guests" User Group
Line 153: Line 158:
  
 :!: Click in ''Security Key'' field to expose the current password. :!: Click in ''Security Key'' field to expose the current password.
- 
-:!: To **restrict guest access**, make sure your guest/access control has the following **Post-Authorization Restrictions**: 
- 
-<file> 
-192.168.0.0/16 
-172.16.0.0/12 
-10.0.0.0/8 
-</file> 
  
 ===== Site Administrators ===== ===== Site Administrators =====
Line 181: Line 178:
 ==== L3 Adoption ==== ==== L3 Adoption ====
  
-http://www.youtube.com/watch?v=y5tkToD_nds+**Docs**: https://help.ui.com/hc/en-us/articles/204909754-Remote-Adoption-Layer-3 
 + 
 +**HowTo**: http://www.youtube.com/watch?v=y5tkToD_nds
  
   - Install AP   - Install AP
Line 311: Line 310:
   - Enable Fast Roaming. **WIFI -> SSID -> Advanced -> Enable Fast Roaming**   - Enable Fast Roaming. **WIFI -> SSID -> Advanced -> Enable Fast Roaming**
  
-===== docker-compose.yml =====+===== Docker =====
  
-Simple version: +<note warning>This example uses an unsupported Docker image.  You probably want to use "linuxserver/unifi-network-application:latest" now.</note>
-<file>+
  
 +Unifi Controller seems to be easy to install, run and update under Docker.
 +
 +==== docker-compose.yml ====
 +
 +=== Simple Version ===
 +
 +<file>
 version: "2.1" version: "2.1"
 services: services:
Line 329: Line 334:
     volumes:     volumes:
       - /root/docker/unifi/config:/config       - /root/docker/unifi/config:/config
 +    networks:
 +      - unifi-net
     ports:     ports:
       - 8443:8443       - 8443:8443
Line 339: Line 346:
 #      - 6789:6789 #optional #      - 6789:6789 #optional
 #      - 5514:5514/udp #optional #      - 5514:5514/udp #optional
 +    healthcheck:
 +      test: curl --fail -k https://localhost:8443/ || exit 1
 +      interval: 5m
 +      timeout: 15s
     restart: unless-stopped     restart: unless-stopped
 +
 +networks:
 +  unifi-net:
 +    name: unifi-net
 </file> </file>
  
networking/wireless/unifi.1683901612.txt.gz · Last modified: 2023/05/12 08:26 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki