Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » networking » switch » zyxel_gs1910
Trace:
networking:switch:zyxel_gs1910

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
networking:switch:zyxel_gs1910 [2014/09/22 17:32]
gcooper 		networking:switch:zyxel_gs1910 [2015/08/12 09:20] (current)
gcooper
Line 7: Line 7:
 http://www.zyxel.com/us/en/products_services/xgs1910_gs1910_series.shtml?t=p http://www.zyxel.com/us/en/products_services/xgs1910_gs1910_series.shtml?t=p
  
-Support Notes: ftp://ftp2.zyxel.com/GS1910-24HP/support_note/GS1910-24HP_V1.00.zip+**Support Notes**: ftp://ftp2.zyxel.com/GS1910-24HP/support_note/GS1910-24HP_V1.00.zip 
 + 
 +**CLI Reference**: ftp://ftp.zyxel.com/XS3900-48F/cli_reference_guide/XS3900-48F_1.pdf
  
 ===== Firmware Updates ===== ===== Firmware Updates =====
Line 17: Line 19:
 ==== Default Login Details ==== ==== Default Login Details ====
  
-|IP Address     |http://192.168.1.1           | +|IP Address     |http://192.168.1.1                                              | 
-|User Name      |admin                        | +|User Name      |admin                                                           | 
-|Password       |1234                         | +|Password       |1234                                                            | 
-|Serial Console |115200,N,8,1,No flow control |+|Serial Console |115200,N,8,1,No flow control                                    | 
 +|Serial Cable   |9-pin straight through, USB serial adapter + USB extension only |
  
 ==== CLI Basics ==== ==== CLI Basics ====
  
-<file>+Reset to factory defaults, at boot up:
  
 +<file>
 +ctrl-c
 +default
 +reset
 </file> </file>
  
Line 131: Line 138:
     - Use a 'Policy Value' of 1 or another unused ID number (just not '0' zero).     - Use a 'Policy Value' of 1 or another unused ID number (just not '0' zero).
     - Set the 'Frame Type' to 'IPv4'     - Set the 'Frame Type' to 'IPv4'
 +    - Set the destination IP address or subnet as the IPMI support provider's external IP address.
     - Set the 'Action' to 'Permit'.     - Set the 'Action' to 'Permit'.
   - The second ACE denies all other traffic from the IPMI device.   - The second ACE denies all other traffic from the IPMI device.
Line 146: Line 154:
 ==== Apply the ACE ==== ==== Apply the ACE ====
  
-  - We apply the ACE to the port with the IPMI device.+:!: We apply the ACL policy to the port with the IPMI device.
  
 :!: We deny all other traffic on that port using an ACE (above), not by changing the 'Action' on the Ports page.  That doesn't seem to work as desired. :!: We deny all other traffic on that port using an ACE (above), not by changing the 'Action' on the Ports page.  That doesn't seem to work as desired.
Line 155: Line 163:
   - Leave the 'Action' as 'Permit'.   - Leave the 'Action' as 'Permit'.
  
-{{ :networking:switch:zyxel_apply_ace.png?direct&650 |}}+{{ :networking:switch:zyxel_apply_ace.png?direct&700 |}}
networking/switch/zyxel_gs1910.1411428779.txt.gz · Last modified: 2014/09/22 17:32 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki