Virtual Architects Support Wiki

User Tools

Site Tools

You are here: start » networking » router » mikrotik_switch
Trace:
networking:router:mikrotik_switch

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
networking:router:mikrotik_switch [2014/03/08 16:04]
gcooper 		networking:router:mikrotik_switch [2014/03/27 11:18] (current)
gcooper
Line 24: Line 24:
  
 <file> <file>
 +/interface ethernet print
 /interface ethernet switch print /interface ethernet switch print
- +/interface ethernet switch port print
-/interface ethernet print+
 </file> </file>
  
-===== Configure a Switch Group =====+===== Configure Switch Groups =====
  
 :!: Here we divide the switch into two switch groups of 17 and 6 ports each. :!: Here we divide the switch into two switch groups of 17 and 6 ports each.
Line 43: Line 43:
 </file> </file>
  
-First, we define two master ports and assign the slave ports:+First, we rename all of the interfaces to match our plan: 
 + 
 +:!: ''ether1'' and ''sfp1'' are WAN interfaces. 
 + 
 +:!: ''ether2'' and ''ether19'' are switch master ports.
  
 <file> <file>
-/interface ethernet+/interface 
 +  set ether1 name=ether1-wan 
 +  set ether2 name=ether2-master 
 +  set ether3 name=ether3-slave 
 +  set ether4 name=ether4-slave 
 +  set ether5 name=ether5-slave 
 +  set ether6 name=ether6-slave 
 +  set ether7 name=ether7-slave 
 +  set ether8 name=ether8-slave 
 +  set ether9 name=ether9-slave 
 +  set ether10 name=ether10-slave 
 +  set ether11 name=ether11-slave 
 +  set ether12 name=ether12-slave 
 +  set ether13 name=ether13-slave 
 +  set ether14 name=ether14-slave 
 +  set ether15 name=ether15-slave 
 +  set ether16 name=ether16-slave 
 +  set ether17 name=ether17-slave 
 +  set ether18 name=ether18-slave 
 +  set ether19 name=ether19-master 
 +  set ether20 name=ether20-slave 
 +  set ether21 name=ether21-slave 
 +  set ether22 name=ether22-slave 
 +  set ether23 name=ether23-slave 
 +  set ether24 name=ether24-slave 
 +  set sfp1 name=sfp1-wan 
 +   
 +print 
 +</file>
  
-set 0 name=ether1-wan +Then we modify the switch configuration:
-set 1 name=ether2-master +
-set 18 name=ether19-master +
-set 24 name=sfp1-wan+
  
-set 2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17 master-port=ether2-master +<file> 
-set 19,20,21,22,23 master-port=ether19-master+/interface ethernet 
 +  set ether3-slave master-port=ether2-master 
 +  set ether4-slave master-port=ether2-master 
 +  set ether5-slave master-port=ether2-master 
 +  set ether6-slave master-port=ether2-master 
 +  set ether7-slave master-port=ether2-master 
 +  set ether8-slave master-port=ether2-master 
 +  set ether9-slave master-port=ether2-master 
 +  set ether10-slave master-port=ether2-master 
 +  set ether11-slave master-port=ether2-master 
 +  set ether12-slave master-port=ether2-master 
 +  set ether13-slave master-port=ether2-master 
 +  set ether14-slave master-port=ether2-master 
 +  set ether15-slave master-port=ether2-master 
 +  set ether16-slave master-port=ether2-master 
 +  set ether17-slave master-port=ether2-master 
 +  set ether18-slave master-port=ether2-master 
 +  set ether20-slave master-port=ether19-master 
 +  set ether21-slave master-port=ether19-master 
 +  set ether22-slave master-port=ether19-master 
 +  set ether23-slave master-port=ether19-master 
 +  set ether24-slave master-port=ether19-master
  
 print print
Line 60: Line 110:
  
 ===== Build Bridges ===== ===== Build Bridges =====
 +
 +:!: Use the master ports for bridging and routing.
 +
 +:!: We don't actually use these bridges here.
  
 <file> <file>
 /interface bridge /interface bridge
-add name=bridge1 comment="Bridge for Port Group 1" disabled=no +  add name=bridge1 comment="Bridge for Port Group 1" disabled=no 
-add name=bridge2 comment="Bridge for Port Group 2" disabled=no+  add name=bridge2 comment="Bridge for Port Group 2" disabled=no
  
 print print
Line 79: Line 133:
 <file> <file>
 /ip address /ip address
- +  add address=172.16.1.2/30 interface=ether1-wan comment="Gateway to Upstream Router" 
-add address=172.16.1.2/30 interface=ether1-wan comment="Gateway to Upstream Router" +  add address=10.10.4.1/24 interface=ether2-master comment="Gateway for Private Subnet" 
-add address=10.10.4.1/24 interface=ether2-master comment="Gateway for Private Subnet" +  add address=xxx.xxx.xxx.xxx/xx interface=ether19-master comment="Gateway for Public Subnet"
-add address=198.167.189.17/28 interface=ether19-master comment="Gateway for Public Subnet"+
  
 print print
 </file> </file>
  
-===== Add Static Routes ===== +===== Configure Basic Networking =====
- +
-/ip route +
- +
-add comment="Default Route" gateway=172.16.1.1 +
  
 +Here we set the host name, DNS servers and the default route:
  
 +<file>
 +/system identity set name=CRS125
 +/ip dns set servers=8.8.8.8,8.8.4.4
 +/ip route add dst-address=0.0.0.0/0 gateway=172.16.1.1 distance=1 comment="Default Route"
 +</file>
  
 ===== Disable Neighbor Discovery ===== ===== Disable Neighbor Discovery =====
Line 103: Line 157:
  
 <file> <file>
-/ip neighbor discovery set ether1-master-local,ether13-master-local discover=no+/ip neighbor discovery set ether2-master,ether19-master discover=no
 </file> </file>
  
networking/router/mikrotik_switch.1394319844.txt.gz · Last modified: 2014/03/08 16:04 by gcooper

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki