User Tools
networking:router:mikrotik_switch
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
networking:router:mikrotik_switch [2014/03/03 15:56] gcooper |
networking:router:mikrotik_switch [2014/03/27 11:18] (current) gcooper |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Mikrotik Switches ====== | ====== Mikrotik Switches ====== | ||
| + | |||
| + | FIXME | ||
| http:// | http:// | ||
| Line 22: | Line 24: | ||
| < | < | ||
| - | /interface ethernet switch print | ||
| - | |||
| /interface ethernet print | /interface ethernet print | ||
| + | /interface ethernet switch print | ||
| + | /interface ethernet switch port print | ||
| </ | </ | ||
| - | ===== Configure | + | ===== Configure Switch |
| + | |||
| + | :!: Here we divide the switch into two switch groups of 17 and 6 ports each. | ||
| - | :!: Here we divide | + | :!: We reserve |
| - | :!: We are routing via the SFP port. | + | :!: We erase all configuration before starting. |
| - | Remove default slave configuration, | + | Reset the router to no configuration: |
| < | < | ||
| + | /system reset-configuration no-defaults=yes | ||
| + | </ | ||
| - | /interface ethernet | + | First, we rename all of the interfaces to match our plan: |
| - | set [find master-port=ether2-slave-local] master-port=none | + | :!: '' |
| - | set 0 name=ether1-master-local | + | :!: '' |
| - | set 12 name=ether13-master-local | + | |
| - | set 1, | + | < |
| - | set 13, | + | / |
| + | | ||
| + | set ether2 name=ether2-master | ||
| + | set ether3 name=ether3-slave | ||
| + | set ether4 name=ether4-slave | ||
| + | set ether5 name=ether5-slave | ||
| + | set ether6 name=ether6-slave | ||
| + | set ether7 name=ether7-slave | ||
| + | set ether8 name=ether8-slave | ||
| + | set ether9 name=ether9-slave | ||
| + | set ether10 name=ether10-slave | ||
| + | set ether11 name=ether11-slave | ||
| + | set ether12 name=ether12-slave | ||
| + | set ether13 name=ether13-slave | ||
| + | set ether14 name=ether14-slave | ||
| + | set ether15 name=ether15-slave | ||
| + | set ether16 name=ether16-slave | ||
| + | set ether17 name=ether17-slave | ||
| + | set ether18 name=ether18-slave | ||
| + | set ether19 name=ether19-master | ||
| + | set ether20 name=ether20-slave | ||
| + | set ether21 name=ether21-slave | ||
| + | set ether22 name=ether22-slave | ||
| + | set ether23 name=ether23-slave | ||
| + | set ether24 name=ether24-slave | ||
| + | set sfp1 name=sfp1-wan | ||
| + | |||
| + | |||
| + | </ | ||
| + | |||
| + | Then we modify the switch configuration: | ||
| + | |||
| + | < | ||
| + | /interface ethernet | ||
| + | set ether3-slave | ||
| + | set ether4-slave master-port=ether2-master | ||
| + | set ether5-slave | ||
| + | set ether6-slave master-port=ether2-master | ||
| + | set ether7-slave master-port=ether2-master | ||
| + | set ether8-slave master-port=ether2-master | ||
| + | set ether9-slave master-port=ether2-master | ||
| + | set ether10-slave master-port=ether2-master | ||
| + | set ether11-slave master-port=ether2-master | ||
| + | set ether12-slave master-port=ether2-master | ||
| + | set ether13-slave master-port=ether2-master | ||
| + | set ether14-slave master-port=ether2-master | ||
| + | set ether15-slave master-port=ether2-master | ||
| + | set ether16-slave master-port=ether2-master | ||
| + | set ether17-slave master-port=ether2-master | ||
| + | set ether18-slave master-port=ether2-master | ||
| + | set ether20-slave master-port=ether19-master | ||
| + | set ether21-slave master-port=ether19-master | ||
| + | set ether22-slave master-port=ether19-master | ||
| + | set ether23-slave master-port=ether19-master | ||
| + | set ether24-slave master-port=ether19-master | ||
| </ | </ | ||
| - | ===== Add IP Addresses to Master Switch Ports ===== | + | ===== Build Bridges |
| - | :!: The SFP port is the gateway. | + | :!: Use the master ports for bridging and routing. |
| - | Here we add IP addresses for the upstream link and the two master switch ports: | + | :!: We don't actually use these bridges here. |
| < | < | ||
| - | /ip address | + | / |
| - | + | add name=bridge1 | |
| - | add address=172.16.1.2/ | + | add name=bridge2 |
| - | add address=198.167.189.17/ | + | |
| - | add address=10.10.4.1/ | + | |
| </ | </ | ||
| - | Then we remove the default management | + | ===== Add IP Addresses to Master Switch Ports ===== |
| - | < | + | :!: To use the SFP port as the gateway, just substitute the name of the interface ('' |
| - | remove numbers=0 | + | |
| - | </ | + | |
| - | ===== Add Static Routes ===== | + | :!: Adjust the IP addressing to your needs. |
| - | /ip route | + | Here we add IP addresses for the upstream link and the two master switch ports: |
| - | add comment=" | + | < |
| + | /ip address | ||
| + | | ||
| + | add address=10.10.4.1/24 interface=ether2-master comment=" | ||
| + | add address=xxx.xxx.xxx.xxx/ | ||
| + | |||
| + | </ | ||
| + | ===== Configure Basic Networking ===== | ||
| + | Here we set the host name, DNS servers and the default route: | ||
| + | |||
| + | < | ||
| + | /system identity set name=CRS125 | ||
| + | /ip dns set servers=8.8.8.8, | ||
| + | /ip route add dst-address=0.0.0.0/ | ||
| + | </ | ||
| ===== Disable Neighbor Discovery ===== | ===== Disable Neighbor Discovery ===== | ||
| Line 88: | Line 157: | ||
| < | < | ||
| - | /ip neighbor discovery set ether1-master-local,ether13-master-local | + | /ip neighbor discovery set ether2-master,ether19-master discover=no |
| </ | </ | ||
networking/router/mikrotik_switch.1393887402.txt.gz · Last modified: 2014/03/03 15:56 by gcooper
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
