Differences

This shows you the differences between two versions of the page.

--- networking:monitoring:wattbox [2015/08/28 15:11]
jcooper
+++ networking:monitoring:wattbox [2015/08/29 17:11] (current)
jcooper
@@ Line 5: / Line 5: @@
 **Documentation**: http://www.av-iq.com/avcat/images/documents/dataSheet/2312.pdf
-Evaluating the WattBox WB-200-IPCE-3 I found it to be a capable remote controlled surge suppressor.  It has the ability to use ICMP to determine if a device/Internet is accessible and do an auto power off/on of a port.  I.E. reboot Cable Modem/DSL to attempt reconnect of Internet.
+Evaluating the WattBox WB-200-IPCE-3 I found it to be a capable remote controlled per port surge suppressor.
-It also can send email alerts on conditions.
+  * It has the ability to use ICMP to determine if a device/Internet is accessible and do an auto power off/on of a port.  I.E. reboot Cable Modem/DSL to attempt reconnect of Internet.
+  * You can schedule unattended power cycle of the ports.
+  * It also can send email alerts on conditions.
+:!: I was not able to make the email option work on Zimbra or Gmail accounts.  Does not appear to support encryption.  It did work with mail.sonoracomm.com.
 ===== Setup =====
@@ Line 13: / Line 19: @@
 http://www.dailymotion.com/video/x16znav_wattbox-wb-200-ipce-3-tutorial_tech
-https://www.youtube.com/watch?v=HDx6FiR_La4
+:!: Default credentials User:admin Password: <none, leave "Password" field blank>
-:!: The videos and documentation will tell you to install the configuration software but I see no reason.  Determine the devices IP address via DHCP log etc. and use browser.
+  * The "Power on Delay" settings are connected to the auto power cycle function triggered by the result of the ICMP availability of a host.  The delay is the amount of time the port will be without power.  Handy for devices that need to be in a certain condition (booted up) before another device comes on.
+  * Auto Reboot must be enabled on the WattBox, disabled by default.
-  * WattBox has their own DynDNS system so you can remotely access the device via HTTP (port configurable) if you forward the port to your WattBox.
+https://www.youtube.com/watch?v=HDx6FiR_La4
-===== OVRC =====
-:!: This device is also OVRC capable in that it touches base with the OVRC mother ship and can be managed from www.ovrc.com.  An OVRC account is necessary.  It asks if you are a reseller at SnapAV or Aisle8 and if you say No you will be stopped from creating an account.  However if you say yes you can still setup an account with any valid email address.
+:!: The videos and documentation will tell you to install the configuration software. This is to find the device on your network. Determine the devices IP address via DHCP log etc. and use your browser making the install unnecessary.
+  * WattBox has their own DynDNS system so you can remotely access the device via HTTP (port configurable) if you forward the port to your WattBox.
+===== Firmware Updates =====
-==== Trigger Dependencies ====
+:!: Firmware updates can only be done with the configuration software.
+https://www.onaisle8.com/wcsstore/ExtendedSitesCatalogAssetStore/attachments/documents/PowerManagement/SoftwareAndFirmware/WB-IP_FirmwareUpdateInstructions.pdf
+===== OVRC =====
-https://www.zabbix.com/documentation/2.4/manual/config/triggers/dependencies
+:!: This device is also OVRC capable in that it touches base with the OVRC mother ship and can be managed from www.ovrc.com.  An OVRC account is necessary.
-Sometimes the availability of one host depends on another. A server that is behind some router will become unreachable if the router goes down. With triggers configured for both, you might get notifications about two hosts down - while only the router was the guilty party.
+:!: Creating and account at OVRC you will be asked if you are a reseller at SnapAV or Aisle8 and if you say No you will be stopped from creating an account.  However, if you say yes you can still setup an account with any valid email address.
+  * With an OVRC account you can have multiple "Accounts" each with there own devices to be managed.
+  * All settings available with the web interface are also configurable via the OVRC panel
+  * To add a device just enter the MAC address of a device that is online.  It will be detected and then you enter the S/N.

Virtual Architects Support Wiki

User Tools

Site Tools

Differences

Page Tools