User Tools
computing:linux:ups:cyberpower
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
computing:linux:ups:cyberpower [2014/06/15 12:52] gcooper |
computing:linux:ups:cyberpower [2023/05/10 14:02] (current) gcooper |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Configure CyberPower UPS Monitoring on Linux ====== | ====== Configure CyberPower UPS Monitoring on Linux ====== | ||
| - | ===== CyberPower PowerPanel for Linux ===== | + | http:// |
| - | :!: PowerPanel | + | ===== PowerPanel |
| - | See also: **[[networking:linux: | + | **Download**: https:// |
| - | See also: **[[networking:linux:ssmtp|SSMTP]]** | + | **Manual**: https:// |
| ==== Installation ==== | ==== Installation ==== | ||
| - | Connect the included USB cable to UPS. You may have problems getting it to work with the serial cable. | + | :!: Tested |
| - | === RPM === | + | :!: Connect the included USB or serial cable to UPS. |
| - | :!: Tested | + | :!: We use the **Local** version for single servers |
| < | < | ||
| - | rpm -Uvh http://www.cyberpowersystems.com/software/powerpanel_123_i386.rpm | + | wget https://dl4jz3rbrsfum.cloudfront.net/software/ppb490-linux-x86_x64.sh |
| + | chmod +x ppb470-linux-x86_x64.sh | ||
| + | ./ | ||
| </ | </ | ||
| - | === Tar === | + | Check that services started: |
| - | + | ||
| - | :!: Tested with SME Server 7.3 and a CyberPower CP1500AVRT UPS. | + | |
| - | + | ||
| - | Download the PowerPanel software to the machine where the UPS is connected: | + | |
| - | + | ||
| - | wget http:// | + | |
| - | + | ||
| - | Unpack and install: | + | |
| - | + | ||
| - | tar -xzvf powerpanel-1.1.tar.gz cd powerpanel-1.1 ./ | + | |
| - | + | ||
| - | ==== Check Communications ==== | + | |
| < | < | ||
| - | pwrstat -status | + | systemctl |
| - | pwrstat -config | + | systemctl status ppbwd.service |
| </ | </ | ||
| - | Verify startup: | + | ==== Access ==== |
| - | < | + | Default credentials: |
| - | chkconfig --list |grep pwr | + | |
| - | </ | + | |
| - | For SME Server only which uses runlevel 7: | + | ^Username ^Password |
| + | |admin | ||
| - | < | + | Use a web browser from a workstation: |
| - | ln -s /etc/rc.d/init.d/pwrstatd /etc/rc7.d/ | + | |
| - | </ | + | **http://ip.of.linux.svr:3052** |
| ==== Configuration ==== | ==== Configuration ==== | ||
| Line 94: | Line 83: | ||
| </ | </ | ||
| - | ==== Testing ==== | + | ===== Testing |
| - | You may want to change the lowbatt-threshold so the box shuts down in a shorter | + | You may want to change the lowbatt-threshold |
| < | < | ||
| - | lowbatt-threshold = 15 | + | lowbatt-threshold = 90 |
| service pwrstatd restart | service pwrstatd restart | ||
| Line 107: | Line 96: | ||
| ===== XenServer ===== | ===== XenServer ===== | ||
| + | |||
| + | :!: These settings are probably not ideal, but are a good start. | ||
| Modifications to above for XenServer: | Modifications to above for XenServer: | ||
| Line 120: | Line 111: | ||
| shutdown-sustain = 600 #set this to a little longer than it takes to shut down all VMs and your server | shutdown-sustain = 600 #set this to a little longer than it takes to shut down all VMs and your server | ||
| lowbatt-threshold = 35 # | lowbatt-threshold = 35 # | ||
| + | lowbatt-duration = 60 #allow the script to run for 60 seconds before the shutdown | ||
| </ | </ | ||
computing/linux/ups/cyberpower.1402858322.txt.gz · Last modified: 2014/06/15 12:52 by gcooper
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
